Torqued binding screws... - Snowboarding Forum - Snowboard Enthusiast Forums
User Tag List

 
LinkBack Thread Tools Display Modes
post #1 of 4 (permalink) Old 03-11-2014, 09:56 PM Thread Starter
-LIFETIME MEMBER-
 
jwelsh83's Avatar
 
Join Date: Jan 2013
Location: East
Posts: 291
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Torqued binding screws...

Hey guys. Curious if any of you have gotten any bindings over the years and had issues with the screws being over tightened from the factory. I recently got a set of Flow NX2 SE's and was going through the paces of setting them up. Removed all the straps and began setting the boot centered to the footbed. Then the problems started... I started with the right foot binding. I was extending the frame of the heel/high back out to give equal over hang of toe vs. heel. The screws to extend the heel were a NIGHTMARE! They were so tight and torqued down, the one side I was able to loosen and move to the other notch but the opposite side, well, not so much. I even watched the set up video flow put out since this was my first pair of flows to make sure I got it right. It called for a #3 phillips, so I used a #3 phillips. Then switched to a flat head that fit, in hopes to loosen the screw...nothing. Didn't budge one bit! Needless to say I ended up stripping the screw head after trying. I didn't attempt drilling out the screw since there was limited room there after. So the only way to get the screw off was to cut the screw with a metal cutting blade, and that's where the cosmetic botching began. A brand new binding, fubar'd from a stripped screw. I contacted flow and they were pretty cool. I told them about the situation and the guy I talked to told me to send him pics of the catastrophe with my address and he'd get back to me tomorrow. The same screws on the left foot binding were tough as well but I was able to loosen those without to much of a fuss and have the binding totally set up. I pretty much told the guy all I needed was the frame with the high back. The straps are okay and the cable could also be salvaged.
jwelsh83 is offline  
Sponsored Links
Advertisement
 
post #2 of 4 (permalink) Old 03-11-2014, 10:22 PM
Senior Member
 
PalmerFreak's Avatar
 
Join Date: Jul 2009
Posts: 422
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Had the same exact problem with a brand new pair of NX2-RS bindings about a month ago. They put Loctite on the screws at the factory and they are a bitch to get loose. If you don't have a long-handle #3 phillips head screw driver you won't have much of a chance of getting them out.

I posted me experience here:

http://www.snowboardingforum.com/bin...2013-q-55.html
PalmerFreak is offline  
post #3 of 4 (permalink) Old 03-11-2014, 10:45 PM Thread Starter
-LIFETIME MEMBER-
 
jwelsh83's Avatar
 
Join Date: Jan 2013
Location: East
Posts: 291
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Quote:
Originally Posted by PalmerFreak View Post
Had the same exact problem with a brand new pair of NX2-RS bindings about a month ago. They put Loctite on the screws at the factory and they are a bitch to get loose. If you don't have a long-handle #3 phillips head screw driver you won't have much of a chance of getting them out.

I posted me experience here:

http://www.snowboardingforum.com/bin...2013-q-55.html
Yeah, they're no joke. I couldn't believe how hard they were to get off. Thank goodness I have my Unions as a back up to still be able to ride. When it's all sorted out, I'm hoping a large is okay with wearing Nike Vapen boots. Seems like Nike boots are so much more wider and I wear a size 10. My Unions are an XL since they're so wide. I think over time they'll start to wear with the flows where the hinge point is on the binding against my boot with repeatedly folding it down. I know a large should technically fit a size 10 boot, but I have my doubts with how wide Nike's are...
jwelsh83 is offline  
post #4 of 4 (permalink) Old 03-11-2014, 11:34 PM
t21
Veteran Member
 
Join Date: Dec 2010
Location: MT.
Posts: 725
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Just a reminder that you need to enter your binding on an angle over the hinge point. I wear 32 boa's sz.10 and large is the right size for the binding.

2015 Rossi One Mag 159
2015 Capita Charlie Slasher 161
NX2-AT
FUSE-AT
t21 is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome