help with binding and toe ramp??? - Snowboarding Forum - Snowboard Enthusiast Forums
SnowboardingForum.com is the premier Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 09-01-2014, 11:39 AM   #1 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default help with binding and toe ramp???

I ride goofy. Left foot angled at 9 and right foot at 12. My right foot toe ramp of the binding hangs over the board about a mm, and baseplate is even with the topsheet b4 edge. What are my options other than the obvious wider board and smaller bindings? Also the toe ramp is set back to its farthest point. Would shaving some off from the connection point cause an issue? They are union factory bindings.. Thank you
ademozbek is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 09-01-2014, 12:05 PM   #2 (permalink)
Member
 
Join Date: Jan 2010
Location: Portugal, Ericeira
Posts: 62
Default

How much is the foot Hanging?
I am also interested in this subject would like to know how to measure the toe and heel overhang is from the edge of the board to the tip of the footprint?
What's your board waist width and your boot size?

Regards
kaipirinha81 is offline   Reply With Quote
Old 09-01-2014, 12:10 PM   #3 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default

Quote:
Originally Posted by kaipirinha81 View Post
How much is the foot Hanging?
I am also interested in this subject would like to know how to measure the toe and heel overhang is from the edge of the board to the tip of the footprint?
What's your board waist width and your boot size?

Regards
The waist width is 250mm boot size 10.5. Boot hang is fine..less than an inch. Its the actual binding toe ramp that concerns me, also baseplate is about even with the board.
ademozbek is offline   Reply With Quote
Old 09-01-2014, 12:13 PM   #4 (permalink)
-LIFETIME MEMBER-
 
Join Date: Sep 2013
Posts: 147
Default

Take a picture of your boot laced up and strapped in the binding on the board from a few angles and post them. You'll get some great advice if the folks on here can actually see what you're describing.
DevilWithin is offline   Reply With Quote
Old 09-01-2014, 12:22 PM   #5 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default

Here are some pics
Attached Images
File Type: jpg 20140901_131816_1409592045892.jpg (63.8 KB, 24 views)
File Type: jpg 20140901_131609_1409592064317.jpg (81.3 KB, 22 views)
File Type: jpg 20140901_131515_1409592083835.jpg (53.4 KB, 21 views)
File Type: jpg 20140901_131502_1409592102635.jpg (70.5 KB, 23 views)
ademozbek is offline   Reply With Quote
Old 09-01-2014, 12:23 PM   #6 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default

Quote:
Originally Posted by DevilWithin View Post
Take a picture of your boot laced up and strapped in the binding on the board from a few angles and post them. You'll get some great advice if the folks on here can actually see what you're describing.
Just posted a few
ademozbek is offline   Reply With Quote
Old 09-01-2014, 01:16 PM   #7 (permalink)
Member
 
Join Date: Jul 2014
Posts: 84
Default

You need different bindings. Send those to me. How did you install the discs? Is the binding centered on the board?

This is an option http://m.youtube.com/watch?v=O_ika6Q8dag
I don't know exactly how it affects board flex but i used some my first season snowboarding because i had an old burton air that i got for free but it was very narrow.

Last edited by taco tuesday; 09-01-2014 at 01:26 PM.
taco tuesday is offline   Reply With Quote
Old 09-01-2014, 01:25 PM   #8 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default

Updated pics after adjustments...should be ok?
Attached Images
File Type: jpg 20140901_142302_1409595866866.jpg (61.4 KB, 21 views)
File Type: jpg 20140901_142253_1409595879716.jpg (58.9 KB, 18 views)
ademozbek is offline   Reply With Quote
Old 09-01-2014, 01:27 PM   #9 (permalink)
Junior Member
 
Join Date: Aug 2014
Posts: 12
Default

Quote:
Originally Posted by taco tuesday View Post
You need different bindings. Send those to me. How did you install the discs? Is the binding centered on the board?
Yes they are.
ademozbek is offline   Reply With Quote
Old 09-01-2014, 01:41 PM   #10 (permalink)
-LIFETIME MEMBER-
 
Join Date: Sep 2013
Posts: 147
Default

I think you'll be fine after the last adjustment. Another option is to widen your stance a bit to make up that mm overhang. I'd try it out as is and see if you get any toe drag before doing much else...looks pretty good to me from those last pics.
DevilWithin is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -5. The time now is 04:40 PM.



Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0 PL2
VerticalSports
Baseball Forum Golf Forum Boxing Forum Snowmobile Forum
Basketball Forum Soccer Forum MMA Forum PWC Forum
Football Forum Cricket Forum Wrestling Forum ATV Forum
Hockey Forum Volleyball Forum Paintball Forum Snowboarding Forum
Tennis Forum Rugby Forums Lacrosse Forum Skiing Forums