Binding Position Across The Board - Snowboarding Forum - Snowboard Enthusiast Forums
User Tag List

 
LinkBack Thread Tools Display Modes
post #1 of 3 (permalink) Old 07-14-2012, 01:31 AM Thread Starter
Junior Member
 
Join Date: Jul 2012
Posts: 17
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Binding Position Across The Board

Hey guys,

just after a bit of advice for my binding setup.

My bindings have 3 screw holes (like this: OOO) on each of the 4 mounting point to adjust where the binding sits across the board.

Question is, does setting the binding more on the heelside or toeside make any difference to the riding?

Mine was set up for me and on one binding the screws are mounted on the middle screw hole and the front binding it is on the heelside screw holes.

Toe and heel going over the board isn't a problem. Both protrude about 1cm but as they're angled they don't tend to be problematic ( +15 / -9 ). I could adjust to any of the 3 and be ok.

Just looking for the optimum setting and/or pros and cons of each config.

Advice much appreciated.
lucasdg is offline  
Sponsored Links
Advertisement
 
post #2 of 3 (permalink) Old 07-14-2012, 02:13 AM
Banned!
 
snowklinger's Avatar
 
Join Date: Aug 2011
Location: L-Town
Posts: 6,554
Mentioned: 1 Post(s)
Tagged: 1 Thread(s)
Quoted: 131 Post(s)
The holes you choose does not matter as long as the boot sits in the middle of the board (equal overhang).

Support Local Business
"Shop Smart. Shop S-Mart!" - Ash
snowklinger is online now  
post #3 of 3 (permalink) Old 07-16-2012, 07:23 PM
Reformed Creep-o-saurus
 
poutanen's Avatar
 
Join Date: Dec 2011
Location: Calgary, AB
Posts: 6,191
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 36 Post(s)
Quote:
Originally Posted by snowklinger View Post
The holes you choose does not matter as long as the boot sits in the middle of the board (equal overhang).
+1 you're looking for equal overhang. There's no such thing as no overhang (unless you're riding like a 12" wide board with size 6 boots!). When I set up bindings I toss the boots in them and ratchet them lightly down, then rock them back and forth while pressing the edge into whatever surface I'm working on. Should be able to get about 60 degrees or so of lean angle in each direction.

If you got a wide board and more angle than that, just make sure they're centred...
poutanen is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome