Chipped the corner of my board - - is it ok??? - Snowboarding Forum

Penguin · 01-21-2009, 01:28 PM

01-21-2009, 01:50 PM

ouch... id definitely get that looked at.

scottland · 01-21-2009, 01:56 PM

Easy fix. Get some 2-part epoxy, mix it up, and slather it over the chip. Wait for it to set most of the way, then take some sand paper or a file, and sand it smooth.

Done.

Penguin · 01-21-2009, 02:56 PM

Quote:

Originally Posted by scottland

Easy fix. Get some 2-part epoxy, mix it up, and slather it over the chip. Wait for it to set most of the way, then take some sand paper or a file, and sand it smooth.

Done.

Thank you sir!!!

01-21-2009, 03:16 PM

my board actually fell over the other day. it isnt that bad. the edge is kind of messed up a little and i can run my fingernail down in between one of the layers of the board..should i use the same thing? or will a small amount of super glue or somethin work?

Penguin · 01-21-2009, 03:17 PM

Coudn't hurt... I'm gonna make a trip to Lowe's on my break.

scottland · 01-21-2009, 03:53 PM

Quote:

Originally Posted by excusemeflow

my board actually fell over the other day. it isnt that bad. the edge is kind of messed up a little and i can run my fingernail down in between one of the layers of the board..should i use the same thing? or will a small amount of super glue or somethin work?

I would use epoxy rather than super glue. Super glue gets brittle when it's cold.

snowjeeper · 01-22-2009, 08:25 AM

same thing happened to my wifes board but the edge is dented in :-/ I'm going to take it to a shop to see how much it would be to get it repaired, but if it's expensive I'll just epoxy it.

01-21-2009, 01:28 PM	#1 (permalink)
Penguin Veteran Member Join Date: May 2008 Location: Burbank, CA Posts: 904	Chipped the corner of my board - - is it ok??? __________________ www.nerdwaffles.com www.thuglifecomics.com www.zombiesociety.com

01-21-2009, 03:17 PM	#6 (permalink)
Penguin Veteran Member Join Date: May 2008 Location: Burbank, CA Posts: 904	Coudn't hurt... I'm gonna make a trip to Lowe's on my break. __________________ www.nerdwaffles.com www.thuglifecomics.com www.zombiesociety.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-21-2009, 01:50 PM	#2 (permalink)
MadRopes Guest Posts: n/a	ouch... id definitely get that looked at.

01-21-2009, 01:56 PM	#3 (permalink)
scottland Senior Member Join Date: Jan 2008 Posts: 232	Easy fix. Get some 2-part epoxy, mix it up, and slather it over the chip. Wait for it to set most of the way, then take some sand paper or a file, and sand it smooth. Done.

01-21-2009, 03:16 PM	#5 (permalink)
excusemeflow Guest Posts: n/a	my board actually fell over the other day. it isnt that bad. the edge is kind of messed up a little and i can run my fingernail down in between one of the layers of the board..should i use the same thing? or will a small amount of super glue or somethin work?

01-22-2009, 08:25 AM	#8 (permalink)
snowjeeper Veteran Member Join Date: Nov 2008 Location: WI Posts: 1,922	same thing happened to my wifes board but the edge is dented in :-/ I'm going to take it to a shop to see how much it would be to get it repaired, but if it's expensive I'll just epoxy it.