I'm a size 10 snowboard boot, 160 lb., and 6'0". I recently purchased a salomon titan 2010 model because it was a good buy, it was my type of board (tapered directional for all mountain riding), its weight capacity was 130-175 lb. and boot size up to 29.5 centimeters.
I did some more research online after making the purchase and found out the board is narrow for size 10. I thought it wasn't because it says on the sticker on the back of the board that it can work with up to a size 11.5 mens boot (29.5 cm), and my boot size would be 28 cm. I don't know why salomon says this board could work with a size 11.5 boot if its narrow even for a size 10. The actual waist width of the board is 247 mm.
So my main worry is, can I make this board work? I know it won't be ideal and that's ok. The board I can't return because it's last years model but I can get any low to mid priced boots/bindings to make it work.
I also have a quick question regarding the boot size. On the sticker it says boot size/pointure (mondopoint) and the corresponding values are 255/295. I know the pointure (mondopoint) is the boot's measurement in cm or in this case mm (295), but what is the boot size exactly (the 255 measurement)? Any suggestions would be great, thank you.
throw your bindings on, throw your boots on, strap into the board on carpet where you have room. Lean on your toe and heel edge. Does it look like it your going to have any drag? Simple enough.
I don't have boots/bindings yet that's the problem. Plus I wouldn't be able to tell if I would have drag or not, I'm not experienced enough.
I did some calculations using a guide on this forum to make this easier for anyone who wants to help me, I'm thinking I just have to adjust binding angles, but I don't know what angles to use
Barefoot measurements
10.25 inches=26.04 cm
Salomon Titan 158 2010 width measurements (at middle of inserts)
Nose: 9 13/16 inches=9.8125 inches=24.92 cm
Tail: 9 11/16 inches=9.6875 inches=24.61 cm
Barefoot should should at least match this measurement or exceed it by up to 1 cm.
Nose: 26.04-24.92=1.12 cm (.12 cm above overhang limit)
Tail: 26.04-24.61=1.43 cm (.43 cm above overhang limit)
I'm not an expert like some other people on here but if your barefoot is longer than the width of the board, I would think that's a bad thing.
If the store won't do anything I would try writing to Salamon and tell them what you have discovered. The board is new even if it's last years model. Maybe they will give you a refund for having the wrong stats listed for the board? Might be worth a shot.
dude i'm not an expert or anything but I just did a bunch of research and bought a board for myself and I'm pretty sure a size ten boot on a 24.7 cm wide board should not cause any noticeable problems at all..
You want a little overhang on your toe and heel to give you leverage over your edges. If your board is 24.7 cm and your boots are 28 cm you should be fine, that's only approx 1.5 cm on each side once you're centered. Overhang will also decrease once you mount bindings on it because the boots will be an additional inch off the deck, and your bindings will be set slightly diagonal on the board instead of straight across once you dial in your angles. I think you're over thinking things dude
Try angles at +15 -15, pretty standard ducked stance. You can play with them from there
And don't cheap out on boots! They are the most important part of your setup and they will make or break your day. Buy boots local and try every brand you can on because they'll all fit your foot differently, you gotta find the brand that works best for you. Get them heat molded and wear them around your house for a few hours before you take them to the hill. This will give you a good indication how they'll feel for you, and if they suck you can take them back (why you buy local). Once you find a exact model of boot you like, research how they'll packout before you settle on a final size
You can definitely gain some room by putting some risers between your binding and board. They can be hard to find but if you are good at making stuff they are easily made. It is just basically a block that raises the binding and boot up away from the edge of the board. A 1/2" vertical riser will give you a lot mor space before dragging the heel or toe.
I have size 12 boots and before I really knew much about sizing I was riding a 24.7 or 24.9 and almost never had any problems. now i ride a 25.2 with zero issues.
Are you sure you are a size 10 boot? I mean, did you actually try some boots on?
I mean, my feet measure ~11" and I wear a size 10 or 10.5. If you are measuring heal-to-toe of 10.25", you're a size 9.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Snowboarding Forum - Snowboard Enthusiast Forums
1M posts
46.6K members
Since 2006
A forum community dedicated to all Snowboarding enthusiasts. Come join the discussion about equipment reviews, tips, traveling, gear troubleshooting, share photos, and more!