Calling 153cm NS EVO owners!! - Snowboarding Forum

twin89 · 03-07-2011, 08:15 PM

Hi, i know there has to be some on this forum considering the abnormal amount of NS love on this forum.

I was just wondering if one of you could measure the width of your board on the base, edge to edge under the inserts for me? in inches or cm, whatever works for you.

I ride a board with a 24.6cm ww and a similar side cut with no drag, however i want to see what the width of the board is under the inserts on the bottom of the board.

my board is a little over 10 inches wide at the middle of inserts. (riding 10.5 DC ceptors)

Thanks if anyone has this board, help a fellow snowboarding addict out =)

snowfiend · 03-07-2011, 08:18 PM

i have the board! but not the will... ill get back to you on that tommorow...

twin89 · 03-07-2011, 09:42 PM

haha sure thing! thanks a lot!

to entice you to do it, this is what i will do with the board when and if i get it...

http://www.youtube.com/watch?v=4w7sV...layer_embedded

snowfiend · 03-08-2011, 02:07 PM

ok so i did the measurements and i hope i got em right and this helps you out. i got 25cm at the inserts where my bindings are at.(2nd holes out from the middle) and a little less than 24 1/2 cm in the middle. this was all measured from the bottom or base

twin89 · 03-08-2011, 04:45 PM

hey, thanks a lot man! helped a ton =)

snowfiend · 03-08-2011, 05:10 PM

good to hear

03-07-2011, 08:15 PM	#1 (permalink)
twin89 Veteran Member Join Date: Jan 2009 Location: Long Beach, CA Posts: 841	Calling 153cm NS EVO owners!! Hi, i know there has to be some on this forum considering the abnormal amount of NS love on this forum. I was just wondering if one of you could measure the width of your board on the base, edge to edge under the inserts for me? in inches or cm, whatever works for you. I ride a board with a 24.6cm ww and a similar side cut with no drag, however i want to see what the width of the board is under the inserts on the bottom of the board. my board is a little over 10 inches wide at the middle of inserts. (riding 10.5 DC ceptors) Thanks if anyone has this board, help a fellow snowboarding addict out =) __________________ Too Fast!

03-07-2011, 09:42 PM	#3 (permalink)
twin89 Veteran Member Join Date: Jan 2009 Location: Long Beach, CA Posts: 841	haha sure thing! thanks a lot! to entice you to do it, this is what i will do with the board when and if i get it... http://www.youtube.com/watch?v=4w7sV...layer_embedded __________________ Too Fast!

03-08-2011, 04:45 PM	#5 (permalink)
twin89 Veteran Member Join Date: Jan 2009 Location: Long Beach, CA Posts: 841	hey, thanks a lot man! helped a ton =) __________________ Too Fast!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-07-2011, 08:18 PM	#2 (permalink)
snowfiend Senior Member Join Date: Jan 2011 Location: Northern Virginia Posts: 139	i have the board! but not the will... ill get back to you on that tommorow...

03-08-2011, 02:07 PM	#4 (permalink)
snowfiend Senior Member Join Date: Jan 2011 Location: Northern Virginia Posts: 139	ok so i did the measurements and i hope i got em right and this helps you out. i got 25cm at the inserts where my bindings are at.(2nd holes out from the middle) and a little less than 24 1/2 cm in the middle. this was all measured from the bottom or base

03-08-2011, 05:10 PM	#6 (permalink)
snowfiend Senior Member Join Date: Jan 2011 Location: Northern Virginia Posts: 139	good to hear