Board width... ha - Snowboarding Forum - Snowboard Enthusiast Forums
SnowboardingForum.com is the premier Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 10-31-2012, 06:17 PM   #1 (permalink)
Junior Member
 
Join Date: Oct 2012
Posts: 14
Default Board width... ha

You guys probably get this question every minute. but here it goes..

Im running Union dlx bindings with 32 86 FT boots. SIZE 12 TWELVE..

I want to know what I can get away with for board width or if i have to get a WIDE board...

Im a rail kid and small jumps.. So im looking at a 151wide horrorscope, but if i can go with a normal board theres like 1000 other boards to choose from..

STANCE = 22.5 , and 15,-15 or like 13-13
gaunt is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 10-31-2012, 10:24 PM   #2 (permalink)
-LIFETIME MEMBER-
 
Wiredsport's Avatar
 
Join Date: Sep 2009
Posts: 2,239
Default

I hope that this helps:

How wide of a snowboard do I need? Where is the width of a snowboard measured? What does width mean in terms of my boot size?

Letís start by talking about measurements, because this is where a lot of the confusion arises. The most common width measurement that is provided by manufacturers is "waist". The waist is measured at the narrowest point near the middle of the board (usually). But like with all things in snowboarding, different brands measure different things. Some measure the midpoint between the tip and tail and call that "waist". Others simply provide a measurement they call, "width", but do not really specify what width they are referring to.

If that has you a bit confused, don't worry, because regardless of where these "waist" measurements are taken, they are not very useful for what they are typically used for. Most people think that this measurement is a good indicator of what foot size a board will handle. It is not, and for a simple reason: you do not stand at the waist, you stand at the inserts. A board's waist measurement is always less than the measurement at the inserts and often the difference is significant. Additionally, two boards with the same waist dimension, may have very different measurements at the inserts, depending on each board's sidecut. Measurement at the center insert is a much better way to compare boards for shoe size compatibility, but for some odd reason, manufacturers do not publish this info.

OK, so now we have told you why we think the commonly provided measurements are pretty silly, but what good does that do you? You still need to know how to figure out the correct width for your new board. Well, here comes. There are two easy steps to getting it right every time.

First, measure your bare foot. It is important that you do not try to use a boot size. It is also important that you measure in centimeters, because the board measurements that you will be comparing to will be in cm. Here is the method that we suggest:

Kick your heel (barefoot please, no socks) back against a wall. Mark the floor exactly at the tip of your toe (the one that sticks out furthest - which toe this is will vary by rider). Measure from the mark on the floor to the wall. That is your foot length and is the only measurement that you will want to use. Measure in centimeters if possible, but if not, take inches and multiply by 2.54 (example: an 11.25 inch foot x 2.54 = 28.57 centimeters).

Second, measure the board you are considering. This measurement is easy. It should be taken at the inserts. Try to measure at the inserts that you will be using to achieve your stance position. If you are unsure about this, simply measure at the center of the insert cluster (that will still be very close). Be sure to measure using the base of the board, not the deck. This is important because the sidewalls on many boards are angled in, and will therefore give you a smaller measurement on the deck than on the base. For our example's sake, let's say the measurement is 27.54 at the center insert.

Still with us? You are almost done. You now have a way to compare foot size to board width where it matters, but how do you interpret this info to get the correct width? Well that depends a little on stance angle. If you ride a 0 degree stance, you will want your foot size to be the same as the width of the board at the inserts or up to 1 cm greater. If you ride at an angled stance, you will want to measure the board across at the angles that you will be riding. Again, you will want your foot to at least match this measurement or exceed it by up to 1 cm. So using our example above, this guy has a foot 28.57 cm that exceeds the board with at the inserts 27.54 cm by 1.03 cm at a zero degree angle. But, when he angles his feet to the 15 degree angles that he rides, voila, he has .10 cm of overhang for a perfect fit.

But wait a second. Are we saying that you should have overhang, even with bare feet? Yes. You will need overhang to be able to apply leverage to your edges and to get the most out of your board. 1/2 inch to 3/4 inch of boot overhang for both toe and heel is ideal, and will not create problematic toe or heel drag. Remember that boots typically add 1/2 at both the toe and heel to your foot measurement from above, due to padding, insulation and the outer boot materials. We do not suggest using the boot length to size boards though, as the extra padding etc, cannot be used well to create leverage, that has to come from your foot itself. We highly recommend that riders do not choose boards where their feet do not come to or exceed the real board width.

OK, that's all well and good, but where can you get the information on board width at the inserts if the manufacturers don't provide it? That's easy. Email the store that carries the board(s) that you are considering. Give them your foot length in cm (and your stance width and angles if you know them). They will be able to provide you with the width at the inserts that you will be using and can factor in your stance angle as well to get you the exact overhang that you will have with bare feet.

PS:

Once mounted, the best way to test is to put your (tightly laced) boots into your bindings and strap them in tightly. It is important that you have the heel pulled all the way back into the bindings heel cup or the test wonít help. On a carpeted floor place your board flat on its base. Kneel behind the heelside edge and lift that edge so that it rests on your knees and so that the toeside edge is angled down into the carpet. Now press down with both hands using firm pressure, one hand on each of the boots. This will compress the board's sidecut and simulate a turn on hard snow. You can change the angle of the board on your knees to become progressively steeper and you will be able to see at what angle you will start getting toe drag. You will want to repeat the test for your heelside as well. If you are not getting drag at normal turn and landing angles, then you are good to go.

PPS:

Also a note about boots: Boot design plays a big role in toe drag as does binding ramping and binding base height. Boots that have a solid bevel at the toe/heel drag less. Many freestyle boots push for more surface contact and reduce bevel. This helps with contact, but if you have a lot of overhang with those boots it hurts in terms of toe drag.

Now go ride!
Wiredsport is offline   Reply With Quote
Old 10-31-2012, 10:41 PM   #3 (permalink)
Member
 
stupidmop's Avatar
 
Join Date: Oct 2012
Location: San Francisco, CA
Posts: 74
Default

I would say that you should go with a wide board.
stupidmop is offline   Reply With Quote
Old 10-31-2012, 11:01 PM   #4 (permalink)
The Rooster King
 
ShredLife's Avatar
 
Join Date: Feb 2010
Location: Oregon
Posts: 3,264
Default

wiredsport i know you mean well, and you think that that "article" is helpful - but it is not. that is completely over-thinking things.

not talking shit - you are helpful to alot of newps on here.

if you wear 12+ get a wide board.
ShredLife is offline   Reply With Quote
Old 10-31-2012, 11:13 PM   #5 (permalink)
Junior Member
 
Join Date: Oct 2012
Posts: 14
Default

would you say 151 is maybe a bit loopy for 6'2 150pounds? or will it just be a nice small jib stick. (horrorscope)
gaunt is offline   Reply With Quote
Old 10-31-2012, 11:28 PM   #6 (permalink)
The Rooster King
 
ShredLife's Avatar
 
Join Date: Feb 2010
Location: Oregon
Posts: 3,264
Default

i don't think its outta line. its about right there for your weight - you're lanky enough that a 153 or 154 maybe even fine as a jibstick but i don't think a 151 is ridiculous..
ShredLife is offline   Reply With Quote
Old 10-31-2012, 11:57 PM   #7 (permalink)
Junior Member
 
Join Date: Oct 2012
Posts: 14
Default

im like 145 in the morning 150 in the day.. and 6'2 so im pretty lanky haha. I also skateboard so i think 151 would be dank. they make 151 wide and 155 wide for the 2012 capita.. theres a ride crush and kink at 153 and a 152 stair master..

horrorscope seems the softest.
gaunt is offline   Reply With Quote
Old 11-01-2012, 07:23 AM   #8 (permalink)
-LIFETIME MEMBER-
 
Wiredsport's Avatar
 
Join Date: Sep 2009
Posts: 2,239
Default

A few things to consider. "Wide" has no specific meaning between brands or even models.

The Horrorscope is a great example. The 151 Wide is 25.7 at the waist which is only .5 cm wider that the same deck in standard. In the Rome Garage Rocker (for instance) the difference between normal and wide is 1 cm and the 151 wide in that deck is 26 cm. Wide decks range from the low 25 cm range to the mid 27 cm range (at the waist).

If you have a minute, please measure your foot using the method below:

Kick your heel (barefoot please, no socks) back against a wall. Mark the floor exactly at the tip of your toe (the one that sticks out furthest - which toe this is will vary by rider). Measure from the mark on the floor to the wall. That is your foot length and is the only measurement that you will want to use. Measure in centimeters if possible, but if not, take inches and multiply by 2.54 (example: an 11.25 inch foot x 2.54 = 28.57 centimeters).

Last edited by Wiredsport; 11-01-2012 at 07:26 AM.
Wiredsport is offline   Reply With Quote
Old 11-01-2012, 08:07 AM   #9 (permalink)
Resident poet
 
wrathfuldeity's Avatar
 
Join Date: Oct 2007
Location: Bham
Posts: 3,820
Default

Wired you ought to copy this to the narrow board thread....its good info about fitting the board to your feet.

Quote:
Originally Posted by Wiredsport View Post
I hope that this helps:

How wide of a snowboard do I need? Where is the width of a snowboard measured? What does width mean in terms of my boot size?

Letís start by talking about measurements, because this is where a lot of the confusion arises. The most common width measurement that is provided by manufacturers is "waist". The waist is measured at the narrowest point near the middle of the board (usually). But like with all things in snowboarding, different brands measure different things. Some measure the midpoint between the tip and tail and call that "waist". Others simply provide a measurement they call, "width", but do not really specify what width they are referring to.

If that has you a bit confused, don't worry, because regardless of where these "waist" measurements are taken, they are not very useful for what they are typically used for. Most people think that this measurement is a good indicator of what foot size a board will handle. It is not, and for a simple reason: you do not stand at the waist, you stand at the inserts. A board's waist measurement is always less than the measurement at the inserts and often the difference is significant. Additionally, two boards with the same waist dimension, may have very different measurements at the inserts, depending on each board's sidecut. Measurement at the center insert is a much better way to compare boards for shoe size compatibility, but for some odd reason, manufacturers do not publish this info.

OK, so now we have told you why we think the commonly provided measurements are pretty silly, but what good does that do you? You still need to know how to figure out the correct width for your new board. Well, here comes. There are two easy steps to getting it right every time.

First, measure your bare foot. It is important that you do not try to use a boot size. It is also important that you measure in centimeters, because the board measurements that you will be comparing to will be in cm. Here is the method that we suggest:

Kick your heel (barefoot please, no socks) back against a wall. Mark the floor exactly at the tip of your toe (the one that sticks out furthest - which toe this is will vary by rider). Measure from the mark on the floor to the wall. That is your foot length and is the only measurement that you will want to use. Measure in centimeters if possible, but if not, take inches and multiply by 2.54 (example: an 11.25 inch foot x 2.54 = 28.57 centimeters).

Second, measure the board you are considering. This measurement is easy. It should be taken at the inserts. Try to measure at the inserts that you will be using to achieve your stance position. If you are unsure about this, simply measure at the center of the insert cluster (that will still be very close). Be sure to measure using the base of the board, not the deck. This is important because the sidewalls on many boards are angled in, and will therefore give you a smaller measurement on the deck than on the base. For our example's sake, let's say the measurement is 27.54 at the center insert.

Still with us? You are almost done. You now have a way to compare foot size to board width where it matters, but how do you interpret this info to get the correct width? Well that depends a little on stance angle. If you ride a 0 degree stance, you will want your foot size to be the same as the width of the board at the inserts or up to 1 cm greater. If you ride at an angled stance, you will want to measure the board across at the angles that you will be riding. Again, you will want your foot to at least match this measurement or exceed it by up to 1 cm. So using our example above, this guy has a foot 28.57 cm that exceeds the board with at the inserts 27.54 cm by 1.03 cm at a zero degree angle. But, when he angles his feet to the 15 degree angles that he rides, voila, he has .10 cm of overhang for a perfect fit.

But wait a second. Are we saying that you should have overhang, even with bare feet? Yes. You will need overhang to be able to apply leverage to your edges and to get the most out of your board. 1/2 inch to 3/4 inch of boot overhang for both toe and heel is ideal, and will not create problematic toe or heel drag. Remember that boots typically add 1/2 at both the toe and heel to your foot measurement from above, due to padding, insulation and the outer boot materials. We do not suggest using the boot length to size boards though, as the extra padding etc, cannot be used well to create leverage, that has to come from your foot itself. We highly recommend that riders do not choose boards where their feet do not come to or exceed the real board width.

OK, that's all well and good, but where can you get the information on board width at the inserts if the manufacturers don't provide it? That's easy. Email the store that carries the board(s) that you are considering. Give them your foot length in cm (and your stance width and angles if you know them). They will be able to provide you with the width at the inserts that you will be using and can factor in your stance angle as well to get you the exact overhang that you will have with bare feet.

PS:

Once mounted, the best way to test is to put your (tightly laced) boots into your bindings and strap them in tightly. It is important that you have the heel pulled all the way back into the bindings heel cup or the test wonít help. On a carpeted floor place your board flat on its base. Kneel behind the heelside edge and lift that edge so that it rests on your knees and so that the toeside edge is angled down into the carpet. Now press down with both hands using firm pressure, one hand on each of the boots. This will compress the board's sidecut and simulate a turn on hard snow. You can change the angle of the board on your knees to become progressively steeper and you will be able to see at what angle you will start getting toe drag. You will want to repeat the test for your heelside as well. If you are not getting drag at normal turn and landing angles, then you are good to go.

PPS:

Also a note about boots: Boot design plays a big role in toe drag as does binding ramping and binding base height. Boots that have a solid bevel at the toe/heel drag less. Many freestyle boots push for more surface contact and reduce bevel. This helps with contact, but if you have a lot of overhang with those boots it hurts in terms of toe drag.

Now go ride!
__________________
wrathfuldeity is offline   Reply With Quote
Old 11-01-2012, 09:43 AM   #10 (permalink)
TLN
Senior Member
 
TLN's Avatar
 
Join Date: Sep 2010
Location: Kazachstan
Posts: 321
Default

with US12 foot - definaetly wide board.
Extra-wide board is a smaller probmlem, then toe-drag. At lest to me =)
TLN is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -5. The time now is 11:30 AM.



Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0 PL2
VerticalSports
Baseball Forum Golf Forum Boxing Forum Snowmobile Forum
Basketball Forum Soccer Forum MMA Forum PWC Forum
Football Forum Cricket Forum Wrestling Forum ATV Forum
Hockey Forum Volleyball Forum Paintball Forum Snowboarding Forum
Tennis Forum Rugby Forums Lacrosse Forum Skiing Forums