Binding position OK or am I risking heel- and toe-bites? - Snowboarding Forum - Snowboard Enthusiast Forums
User Tag List

Reply
 
LinkBack Thread Tools Display Modes
post #1 of 14 (permalink) Old 01-02-2013, 03:49 PM Thread Starter
Junior Member
 
Join Date: Dec 2012
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Is the binding too large for my new board? Am I risking heel- and toe-drag?

Hello,

what would you say, is the binding too large for this board? My previous board had a larger waist width than this one and now I don't feel so good about it because the heel and the toes are hanging over the front- and backside and I don't want to risk heel- and toe-drag.

Rotation is -15 and I only mounted one binding yet, the other one will be +15. It is positioned to the side as much to the frontside as possible, already.

Binding is a Cartel L and the Boots are Salomon Maori in 42 / US 9. The board is a non-wide GNU RIder's Coice.















Last edited by someguy; 01-03-2013 at 03:40 AM.
someguy is offline  
Sponsored Links
Advertisement
 
post #2 of 14 (permalink) Old 01-02-2013, 04:00 PM
Veteran Member
 
schmitty34's Avatar
 
Join Date: Dec 2007
Location: Probably at work wasting time
Posts: 889
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Always hard to tell from pics, but size 9 boots should be just fine on a non-wide RC.

There isn't much else your binding position can do to reduce the overhang unless you started using some pretty extreme angles. As long as your boot is centered on the board it should be fine.
schmitty34 is offline  
post #3 of 14 (permalink) Old 01-03-2013, 03:38 AM Thread Starter
Junior Member
 
Join Date: Dec 2012
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks for the input. I thought maybe the Binding is too large and so I have to change to an M version of the Cartel. I bought it some years ago and my previous board had more waist width so that wasn't a problem before. But now it is a problem, maybe.




Last edited by someguy; 01-03-2013 at 03:40 AM.
someguy is offline  
post #4 of 14 (permalink) Old 01-03-2013, 03:45 AM
-LIFETIME MEMBER-
 
Extremo's Avatar
 
Join Date: Nov 2008
Location: NH
Posts: 3,571
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Looks good. You always want some overhang. Otherwise you'd have a hard time getting the board on edge. I'd say that's about normal. Unless you're in the deep stuff you shouldn't run into a problem.
Extremo is offline  
post #5 of 14 (permalink) Old 01-03-2013, 10:52 AM
Veteran Member
 
Join Date: Nov 2011
Location: Seattle, WA
Posts: 1,283
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Somethings not right. For starters you should be in a medium binding with a sz 9 boot and in the 3rd pic (iirc) there's about an inch, inch and a half gap between the back of your boot and the heel cup. I'd start by making the binding as small as possible and going from there.

cliaflpe43t5.jpg
bseracka is offline  
post #6 of 14 (permalink) Old 01-03-2013, 11:04 AM
Veteran Member
 
schmitty34's Avatar
 
Join Date: Dec 2007
Location: Probably at work wasting time
Posts: 889
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Quote:
Originally Posted by bseracka View Post
Somethings not right. For starters you should be in a medium binding with a sz 9 boot and in the 3rd pic (iirc) there's about an inch, inch and a half gap between the back of your boot and the heel cup. I'd start by making the binding as small as possible and going from there.

Attachment 9520
ahhh....good eye. I wasn't really looking at the binding too much, just the boots. Size 9 boots should have no problem with his board, but the L bindings might be too large for his boots.
schmitty34 is offline  
post #7 of 14 (permalink) Old 01-03-2013, 11:33 AM Thread Starter
Junior Member
 
Join Date: Dec 2012
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Quote:
Originally Posted by bseracka View Post
Somethings not right. For starters you should be in a medium binding with a sz 9 boot and in the 3rd pic (iirc) there's about an inch, inch and a half gap between the back of your boot and the heel cup. I'd start by making the binding as small as possible and going from there.

Attachment 9520
This is because the angle of the Cartel highback is not the same as the angle of the calves-part of the boot. You can of course vary the angle of the highback, but it is set as much upright as possible, already. If I'd vary it, the highback would be more "horizontally" and the space between the heel and the heel cup of the binding would be even larger.

Up to now I thought that this wouldn't be a problem because at the upper part the boot presses against the highback and so I can put force to the backside. So you think that this is a major problem?

Maybe the problem persists with a Cartel in size M because the angle of the highback stays almost the same, doesn't it? I had a Cartel in M before, but I gave it back because I felt like the straps were a bit too short for the boots. Maybe I have to change to some other binding. Could you recommend one? Should be good for all-mountain riding (70% onpiste/groomers, 20% offpiste/frontcountry, 10% park). I looked at the Rome 390 Boss before and maybe I'll get them. I also like the idea of canting pads because I have some knee issues.

Last edited by someguy; 01-03-2013 at 11:45 AM.
someguy is offline  
post #8 of 14 (permalink) Old 01-03-2013, 11:53 AM
-LIFETIME MEMBER-
 
herzogone's Avatar
 
Join Date: Oct 2010
Location: Auburn, MA
Posts: 320
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Blog Entries: 98
Quote:
Originally Posted by someguy View Post
This is because the angle of the Cartel highback is not the same as the angle of the calves-part of the boot. You can of course vary the angle of the highback, but it is set as much upright as possible, already. If I'd vary it, the highback would be more "horizontally" and the space between the heel and the heel cup of the binding would be even larger.

Up to now I thought that this wouldn't be a problem because at the upper part the boot presses against the highback and so I can put force to the backside. So you think that this is a major problem?

Maybe the problem persists with a Cartel in size M because the angle of the highback stays almost the same, doesn't it? I had a Cartel in M before, but I gave it back because I felt like the straps were a bit too short for the boots. Maybe I have to change to some other binding. Could you recommend one? Should be good for all-mountain riding. I looked at the Rome 390 Boss before and maybe I'll get them. I also like the idea of canting pads because I have some knee issues.
You should force the boot all the way back against the heelcup, the upper part of the boot will just flex forward from the highback as needed. It's a little hard to tell from the pics with your boot loose in the bindings, but it does look to me like the bindings might be a little big for the board. It would be easier to judge that without the boots there at all. If you have room to shift the bindings towards the toeside edge a little without significant footbed overhang, then it might be ok.
herzogone is offline  
post #9 of 14 (permalink) Old 01-03-2013, 11:55 AM
Senior Member
 
Join Date: Nov 2010
Location: Auburn,CA
Posts: 403
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
I have size M cartels as well as size 9 salomon savage boots and they fit great, I would think a L would be a bit big for your boots?
kctahoe is offline  
post #10 of 14 (permalink) Old 01-03-2013, 12:11 PM
Veteran Member
 
Join Date: Nov 2011
Location: Seattle, WA
Posts: 1,283
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Large is to big. If his heel was all the way back in the cup there would be no overhang at the toes and he could move the binding closer to his toe edge. The gas pedal also needs to be on the smallest setting and even then may be to far forward to provide any leverage. Toe straps also look about maxed out on the smallest setting

Do you have have a friend that knows gear that can help you with your bindings? If it's not to late I'd exchange them for a medium. If you've already used them I would talk to the shop and see if they are willing to work with you especiaaly if their employee put you in a large binding.
bseracka is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome