edges be trippin - Snowboarding Forum

JordanAK · 01-08-2013, 12:11 AM

hey my dumbass did this in the park the other day
what can I do to fix it and if I don't what will happen?

BurtonAvenger · 01-08-2013, 12:54 AM

You want the ghetto fix or the real fix?

snowklinger · 01-08-2013, 12:57 AM

put it between 2 piece of metal and smash it with a hammer till its more flat than that and then cover the whole thing in shoo goo.

Soft · 01-08-2013, 01:26 AM

I would just have gone with the "deliver it to the local snowboard shop technique", who usally knows what to do. Either they can do it for a small fee, or can give you some "to-do", and not "to-do".

- P

BlackhawkDriver · 01-08-2013, 01:28 AM

get a new board

JordanAK · 01-08-2013, 03:08 AM

do me up with a ghetto fix so I can go shred tomorrow

walove · 01-08-2013, 09:06 AM

if only your board didnt have edge wrapped around the tip and tail...

BurtonAvenger · 01-08-2013, 09:51 AM

Quote:

Originally Posted by JordanAK

do me up with a ghetto fix so I can go shred tomorrow

Slap duct tape over it. Or put some 2 part epoxy on it then slap duct tape over it.

Yes WAlove cause a tucked edge is so superior. Have fun blowing contact points out.

redlude97 · 01-08-2013, 10:02 AM

Quote:

Originally Posted by JordanAK

do me up with a ghetto fix so I can go shred tomorrow

Take a c-clamp to it

Clayton Bigsby · 01-08-2013, 10:19 AM

I think you'd be better off just leaving it alone, start messing with it and your ptex/topsheet will separate. It's going to hurt anything, if you have any expose fiberglass gore, maybe squirt a little super glue on it.

01-08-2013, 12:11 AM	#1 (permalink)
JordanAK Junior Member Join Date: Jan 2013 Posts: 4	edges be trippin hey my dumbass did this in the park the other day what can I do to fix it and if I don't what will happen?

01-08-2013, 12:54 AM	#2 (permalink)
BurtonAvenger Veteran Member Join Date: Aug 2007 Location: Mountains Posts: 8,031	You want the ghetto fix or the real fix? __________________ Angry Snowboarder Because someone has to call it how they see it!

01-08-2013, 12:57 AM	#3 (permalink)
snowklinger Veteran Member Join Date: Aug 2011 Location: fuck boulder Posts: 2,815	put it between 2 piece of metal and smash it with a hammer till its more flat than that and then cover the whole thing in shoo goo. __________________ is it late october yet?

01-08-2013, 09:06 AM	#7 (permalink)
walove Veteran Member Join Date: May 2009 Location: Bozeman/Seattle Posts: 659	if only your board didnt have edge wrapped around the tip and tail... __________________ SHRED HAPPENS

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-08-2013, 01:26 AM	#4 (permalink)
Soft Junior Member Join Date: Jan 2013 Posts: 13	I would just have gone with the "deliver it to the local snowboard shop technique", who usally knows what to do. Either they can do it for a small fee, or can give you some "to-do", and not "to-do". - P

01-08-2013, 01:28 AM	#5 (permalink)
BlackhawkDriver Member Join Date: Dec 2012 Location: South Korea Posts: 31	get a new board

01-08-2013, 03:08 AM	#6 (permalink)
JordanAK Junior Member Join Date: Jan 2013 Posts: 4	do me up with a ghetto fix so I can go shred tomorrow

01-08-2013, 10:19 AM	#10 (permalink)
Clayton Bigsby Senior Member Join Date: Oct 2012 Posts: 193 Blog Entries: 1	I think you'd be better off just leaving it alone, start messing with it and your ptex/topsheet will separate. It's going to hurt anything, if you have any expose fiberglass gore, maybe squirt a little super glue on it.