|Topic Review (Newest First)|
|02-13-2011 09:11 PM|
Okay, I'll admit that I laughed out loud at the mysterious snow mounds question. Not really at you but it is funny seeing things from the perspective of a beginner again. Even for a lot of experienced riders moguls can be challenging and not much fun (although some people love them). I'm not a big fan. Just avoid them for now.
Don't worry about minor damage to the board. It will happen. Kind of like scratches and dents in your car, the first one hurts the most. Core shots (where a rock takes such a big gouge out of the base that you can see the wood core) are something you should get repaired, but small scrapes aren't a big deal. No sense getting worked up about wear and tear (of course to be a real snowboarder you might want to be aggro and go totally apeshit when someone accidentally bumps into you in the lift line - kidding!).
|02-13-2011 05:08 PM|
Originally Posted by paras View Post
|02-13-2011 03:42 PM|
|paras||Bones speaks of the truth. I'm all about KUU Cold Graphite. Especially on a race day, I like to drip some in my cereal for good measure.|
|02-13-2011 12:28 PM|
Originally Posted by Nefarious View Post
I'm using KUU cold graphite on East Coast ice and have found it outlasts any other regular wax I've tried.
|02-13-2011 12:07 PM|
YES!! I will consider it character, I think it happened when a kid skier fell backwards near me, but nothing i can do.. I'm sure I ran into a fair amount of people my first few times too. I think I have made some progress even though it still take me alot of guts to make that toe turn on blue, at least I'm not really that afraid of that kind of steepness (blue that is). And knowing that leaning down hill is actually staying vertical, and this is the only way for me to initiate that toe turn, if i get scared and lean on my rear legs, no matter how hard i turn my front knees/toes, shoulder, my board just won't turn!!
And something really funny, I never understood what "board is traveling straight from nose to tip". In my mind, the board is a hard piece of wood, how in the hell would it not be straight and be bent??? Isn't nose to tip always straight?? I neglected that it was TRAVELLING!!
My question would be, I could be carving my traverse across the slope where no side slipping is going on, does this mean that as long as there is no side slipping, I can flatten my board (still using the front foot steering technique snowolf taught me) and change edge even though my board is not pointing straight down the fall line (parallel)? I always carve the traverse and skid into the turn and I make sure that my board is pointing straight down the slope and flat before I initiate the turn to the other edge. So what happen is my traverse is very fast, then as I skid into my turn it slows way down, then i point my board, flatten it, and carve my traverse on my other edge, (when it's toe side, there is less carving and much more skidding because of fear...
|02-13-2011 10:30 AM|
Yeah I used to be so careful but one day I just realized that it does not matter that much and it is going to happen anyways so what am I scared of?
Now each first trip on a new board I can't wait to scratch it so I can get over it being in "Perfect" condition.
|02-13-2011 09:58 AM|
Originally Posted by Smokehaus View Post
|02-13-2011 01:57 AM|
|Smokehaus||Yeah don't worry about that scratch at all. I know snowbaords look nice and pretty but if you actually ride the board you are gonna get some minor damage, it is a piece of equipment and scratches give it character IMO.|
|02-13-2011 01:47 AM|
Originally Posted by Robocop View Post
To the OP:
Don't get upset with yourself for not being as confident on a blue run, that will come in time. Tell yourself that you'll be in more control when you get off the flat base and onto your toes and in a short while it will seem like nothing. As to your waxing question, as said above never leave the iron sitting in one spot on the board, that is your main concern with waxing. You can find really cheap irons at thrift stores if need be, wax scrapers don't cost too much and if you are going to stick with snowboarding I suggest buying wax in bulk or finding the largest bar for your needs. Since you're not racing or anything now, just grab some all-temp wax and that will suit you fine.
Edit: You're bound to get minor scratches on the base, don't freak out if you do, but waxing can help keep things looking good on the base.
|02-12-2011 06:49 PM|
Originally Posted by Donutz View Post
|This thread has more than 10 replies. Click here to review the whole thread.|