|Topic Review (Newest First)|
|12-20-2012 08:49 AM|
I am riding an 3 year old pair of Burton Tributes, size 11 with 2013 NX2-AT bindings for about a month now and find them to be very solid with no issues whatsoever.
Make sure you have the power strap centred on your boot. You should have the same amount of ladder strap on each side of your foot, both front and back. Take the time OFF the hill to get your boot / binding setup very close to ideal. If you have done this, you should only have some very minor tweaking to do once you are riding.
Also check to see where the canting pad is positioned. It is adjustable, ( small screw under your heel which is a huge ice magnet, only minor downside that I have discovered) and see if moving it will help with your issue.
|12-20-2012 08:04 AM|
I meant to mention it earlier but boot fit has a huge effect on how well Flows work. More then any other binding. If there is nay slop in the boot then that will go right to the binding.
I really want to encourage you to try out a drastically different stance for a whole day. Something closer to 18/-15 and 22" wide. Also a great way to see what your natural stance is is to stand on your board in socks with no bindings on it with your shoulders in line with the board. Then close your eyes and do full squats (thighs parallel to the ground) As you do the squats adjust your feet (angle and width) until you feel it is as comfortable and "controlled" as possible.
|12-19-2012 11:57 PM|
yeah, I think when i was picking boots, I was picking for the wrong reason. I was wanting ones with a small imprint. I held up 10.5 Burtons with 10.5 Salomons and and the Burtons were an inch smaller. I went with the Burtons to get less toe and heel drag. I learned my lesson. But I think we finally got the boots set up with the proper support. When I go up again and the boots still don't work, I will probably look at new boots, ones with more ankle support.
Not trying to knock the NX2s, they are great bindings. Just need to get the right setup for me. I think I want to try a non canted pair since that is what I am used to riding. Riding a 20 year old board and now going to a totally new everything take a bit of getting used to. I was kinda shocked they don't have 3 strap bindings anymore.
|12-19-2012 11:20 PM|
You got fit poorly for boots, that's a start. And 19-20in at 5'9 is your other issue. Widen you stance. At your height a minimum of 21, especially with a 3* canted binding.
NX2's are a responsive and supportive binding. If you don't like the way they ride that's fine.
|12-19-2012 10:44 PM|
|CK93||to follow up, I was able to get my back binding dialed in right. the front is still an issue. I had to tightened the ankle strap when I was boarding, then loosen it a bit while on the lift. I couldn't find a happy medium. But i was having serious heel lift with my front as well. I took my boot back to Christy's and they did a bit more molding to the boot. Hopefully this helps. They are getting better. I think I used to old school. The bindings I rode before this had 3 straps on them. Burton Flex bindings from the 90's. They are still in good, but trying to get with the times with newer bindings. I think part of it is I am used to a binding with no movement at all from the calf down. Thinking I need to bindings with an actual ankle strap instead of the pad on Flow's. Don't get me wrong, the Flow's are good, but for me, I need something a bit more ankle support.|
|12-19-2012 10:34 PM|
|CK93||5'9" 210 lbs|
|12-19-2012 09:08 PM|
Originally Posted by CK93 View Post
|12-19-2012 08:32 PM|
|CK93||my width is 19 to 20 inches depending on the board. I usually keep my foot close together. my front foot is 24 and back foot is 12. I like the higher angles.|
|12-17-2012 02:40 PM|
|BurtonBindings||Just curious, what stance angles and width are you running.|
|12-16-2012 09:54 PM|
|CK93||Cool thanks. I am going up to Keystone tomorrow and I won't tighten them as much and see if that helps.|
|This thread has more than 10 replies. Click here to review the whole thread.|