Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Cost and effectiveness of repairing a board... Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
05-03-2013 10:25 AM
snowklinger solid thread ty boys
05-03-2013 08:52 AM
Lamps
Quote:
Originally Posted by BoardWalk View Post
Still laughing.........
+1

19 char
05-02-2013 02:53 PM
BoardWalk
Quote:
Originally Posted by ShredLife View Post
i just fucking said that.
Still laughing.........
05-02-2013 02:11 PM
timmytard
Quote:
Originally Posted by ShredLife View Post
i just fucking said that.
Get rid of that fuckin' homo

Last year, I walked into some store & some old scowlly faced fucker had that bird shirt on.
I instantly started laughing.

Homeslice, just doesn't have the bite that Johnny does.


TT
05-02-2013 01:41 PM
ShredLife
Quote:
Originally Posted by timmytard View Post
Get a couple little screws to use as wedges to open it up.
Just a couple turns should do.

If you can find a bamboo bbq skewer, they are really tough & makes for a deadly thin spatula

sand/file down one end flat like a spatula, use that & a hair dryer to get the epoxy deep under there.

The heat will make the epoxy go a little runnier, smear it around with your spatula.

Clamp. don't touch it for @ least a day.

Most important part.
After you're done, take a file & slightly round down the 90 degree angle of the top sheet.
Not just @ the area you fixed, the whole nose & tail.

That will prevent it from happening again
http://upload.wikimedia.org/wikipedi...6/Fr-voila.ogg


TT
i just fucking said that.
05-02-2013 01:40 PM
timmytard Get a couple little screws to use as wedges to open it up.
Just a couple turns should do.

If you can find a bamboo bbq skewer, they are really tough & makes for a deadly thin spatula

sand/file down one end flat like a spatula, use that & a hair dryer to get the epoxy deep under there.

The heat will make the epoxy go a little runnier, smear it around with your spatula.

Clamp. don't touch it for @ least a day.

Most important part.
After you're done, take a file & slightly round down the 90 degree angle of the top sheet.
Not just @ the area you fixed, the whole nose & tail.

That will prevent it from happening again
http://upload.wikimedia.org/wikipedi...6/Fr-voila.ogg


TT
05-02-2013 12:49 PM
Epic
Quote:
Originally Posted by Casual View Post
And some wax paper... don't epoxy your clamp to your board
Haha there is an 80% chance I would have done that. Thanks guys! I'll let you know how the repair goes.
05-02-2013 12:38 PM
Casual
Quote:
Originally Posted by ShredLife View Post
just epoxy and clamp.
And some wax paper... don't epoxy your clamp to your board
05-02-2013 12:38 PM
Cr0_Reps_Smit it's a little hard to tell from the picture but i would say all you need is to slap enough epoxy in there to seal up the core and just let it dry.

at most you might need to vice grip it down if the edge and top sheet are separated but it doesn't look that bad from the pic.

if there is a gap you can use something like a tooth pick to push some of the epoxy inside of it, spread a little more over it, then grip it down. you can use pieces of card board to protect your top sheet and base when using vices.
05-02-2013 12:36 PM
ShredLife just epoxy and clamp.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome