Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Binding Fix Suggestions? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
05-18-2014 12:25 PM
Originally Posted by Mizu Kuma View Post
...Loctite is a thread locker, and therefore needs an actual thread/thread contact for it to work!!!!!
Yup... tried loctite blue, no dice.

Originally Posted by Mizu Kuma View Post
Sent a pack of Brillo Pads?????
Ha ha, nothing that exotic...
I contacted Flow for tips/ideas on how to fix. Wasn't expecting much since this could easily have been normal wear or operator error. Customer Service responded that they'd take a look if I mailed them my bindings. So I did and got a brand new pair by return mail.
05-17-2014 09:26 PM
Mizu Kuma Sent a pack of Brillo Pads?????
05-17-2014 08:09 PM
Oldman What did they do for you?
05-17-2014 05:51 PM
Flow Customer Service ROCKS!!!

Yup, others have said it on here before. Now I've experienced it firsthand. The guys at Flow are a class act. . Problem fixed.
05-01-2014 03:05 PM
Originally Posted by FalseFlag View Post
Reading skills for some guys suck on here.
+ 1

Then there is the concept of "comprehension"?
04-29-2014 09:01 AM
Lamb And that's where the steel wool comes in.
04-29-2014 08:50 AM
Mizu Kuma From the op I took it as though the thread was stripped?????

Loctite is a thread locker, and therefore needs an actual thread/thread contact for it to work!!!!!
04-29-2014 08:42 AM
Lamb You could also try using a little bit of steel wool. Wrap a bit around the screw threads and tighten to snug. I usually use a drop of loctite and I don't see an issue with it if you use a little of the blue in this application, less is more. Loctite will not pull threads out, using too much will. A screw driver being tapped with a hammer while turning will break the fastener from loctite.
04-29-2014 07:03 AM
Great Ideas...

Thanks all and if there are any other suggestions, keep them coming...

Now I have several options to try out.

Yeah, Manic, just the footbed going into the binding. Small screw, less than 1/2" in length.

To get to the binding screws, I have to remove the footbeds. So this cannot be a "permanent" fix.

I too emailed Flow yesterday... waiting to hear from them. Not sure if replacement is a solution. Seems to me, replacement would mean replacing the baseplate... which is pretty much replacing the whole binding.

Screw and hole in baseplate are metal, so loctite will work.
04-29-2014 12:28 AM
Mizu Kuma Get yourself a cheap tap and die set, and as been suggested make the original hole a little larger, get a suitable screw and Bob ya Uncle!!!!!

Don't use loctite on plastics cause it can have a bad reaction to some, and you'll most certainly be off to the shops for a new pair!!!!!

Also as has been suggested might be worthwhile seein if there's a helicoil that's suitable!!!!!
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome