Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: silly: help: board stance width? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-24-2010 02:45 PM
earl_je tailor's tape should be in inches shouldn't it? idk...

here's what I posted on your other thread:

I'm assuming those numbers are the holes. Here's what you do, grab a measuring tape, figure out the distance between the center of the two discs. That's your stance length.

Also, when I set-up my friends boards, I measure their shoulder width (to make it square with your body/base of support) and shin length (to make it square with your knees) and either average it, or use somewhere in between those two.

Another tip is jumping up on a flat surface as high as you can bending your knees towards your chest, land flat on the ground the measure the length between the middle of your feet. That would be your comfort zone (which I think will be too narrow for most).
03-24-2010 02:24 PM
arsenic0 Ha, now thats funny!
03-24-2010 01:31 PM
lorcar I am writing here again for future readers, it was my mistake, I was using a wicked tape!!! a tailor measure tape! i had no clue these people uses a different system!
03-24-2010 01:09 PM
arsenic0 I dont know about this whole shin measurement...

The standard starting width as far as i knew was shoulder width or slightly larger.

Are you measuring from the center of the binding plate?

The easiest way I had friends check that didnt know where to put theres was have them do a good running jump and land with both feet at the same time and try not to move from that landing position like a gymnast. Generally you will subconsciously spread your legs out and brace for impact at a comfortable width where your body feels safe. May work, may not *shrug*

Assuming your measuring right, your hips will likely hate you a few runs in if your 5'11 with a 27" width...
03-24-2010 12:52 PM
lorcar oh no probl, I didnt feel offended! we do use metric, but I didnt write metric as the stance on board specs are not.
I am asking: how long is your shin? barefoot, from the ground to your knee patella?
03-24-2010 12:47 PM
luke89 Im 6 feet tall and thats what I ride haha. Idk man. What I mean by width is from the center of the binding on your left foot to the center of the binding on your right foot. 20in doesnt seem like much to me. A buddy rides 22 hes taller than me but still. But you do whatever your comfortable with i mean your the one riding. Just thought id throw advice ive gotten out there.
Edit: And sorry for the metric system assumption, you said your english wasnt good and most other countries use metric. I figured id save you the trouble of converting it. Sorry didnt mean to seem like a dick
03-24-2010 12:44 PM
lorcar i simply measured my shin length. It's around 27/28 (no metric system) so I set it up like this on the board. I am 5'11. I cant see a guy tall 6' having it at 20 inches
03-24-2010 12:35 PM
luke89 It depends on how tall you are for stance width. From center to center of the bindigs if you are around 6'0 it is 20-21 inches. Google it and there should be a table saying how wide you should be according to your height. Wider stance= more stability harder to turn. Narrow = easier to turn less stability. Hope this helps
Edit: 20 in = 50.8 cm. Im guessing you use the metric system.
03-24-2010 12:21 PM
Originally Posted by lorcar View Post
ok my english is poorer than I thought
let's try with a sketch of those holes where bindings go

7 6 5 4 3 2 1 ----- 1 2 3 4 5 6 7
7 6 5 4 3 2 1 ----- 1 2 3 4 5 6 7

When I read on K2 website that the Podium has a STANCE WIDTH of 21, what does that refer to?
On the podium (at least a new one) the suggest mounting holes are highlighted. The middle of the four suggested from one binding, to the other suggested for the other binding is 21. I am guessing that the areas you mark (2-4, and 4-2) are suggested on the podium.
03-24-2010 11:41 AM
lorcar i am mounting Union data L-XL on K2 podium 159
i used around 27-28 as stance width
now I am worried about my Northwave decade SL fitting in the bindings, and tweaking the latter...
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome