Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: question about flex Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
05-14-2010 09:59 PM
hondarider17 Just pulled mine off the clamps. Its definetely rockered. I would say its kind of like the Jibstick, close to being flat but comes up a tiny bit at the nose and tail. I used a heat gun. Im gunna rocker it more but this time im using a iron with a cloth underneath
05-14-2010 09:53 PM
bubbachubba340 Now, go make that Super Pow board. Make sure you spray paint a red "S" in the middle of the board too.
05-14-2010 09:35 PM
BurtonAvenger Bah we used to make rockered skis and decks as a joke years ago. Flip the board over, put something that lifts the deck up from the center, tie down both ends, then heat it up. How you want to heat it is up to you. I found that leaving a torpedo heater on the deck did wonders, but we've used heat guns, irons, whatever. We also used to cut slits into the base width wise so it takes out material then when its heated it melts back together.
05-14-2010 09:20 PM
MistahTaki i didnt use the clamps but i got 90 lbs of weight put it on the center of the board with each of it's tips on a chair and ran an iron across the base for about 5 minutes until it got pretty hot. I then pressed on the center of the board with my own weight for about 30 seconds and left the weights on the board. I suggest you should give it more time for it to permanently stick.
05-14-2010 08:42 PM
hondarider17 How long did you run the iron on the base?
and how long did you keep it in the clamps?
05-14-2010 04:55 PM
MistahTaki yea that's what i did i put a wet cloth to cover the iron and i ran it across my base and it worked
05-14-2010 12:29 PM
walove could try a wet cloth with the iron, one post in the teton thread someone use that method and seemed to work. Got some spare time today might give some nose rocker a shot.

Note: From my understanding of epoxies (one year of research work), the outcome of this process depends mostly on the temperature that was used while in the press when first making the board. Epoxy is a plastic and with most plastics it will become softer when heated. When the epoxy is risen above the temperature it was first cured at (150f-180f with snowboards) it is able to make new cross-links (molecular bonding holding the epoxy together). When all has cooled these new cross-links will hold the new shape. If the epoxy gets too hot (above 400f) it will start to burn and break down, this will destroy your board. So reaching a temperature between those two is key. Using boiling water or a wet cloth and iron will keep temps lower and more consistent then direct heat from a heat gun.
05-13-2010 08:48 PM
MistahTaki Update! After I left around 90lbs on the center of the board for about 6 hours I noticed that the flex got little softer. Afterwards I got an iron put a cloth around it and ran it across the base of the board for a little bit with the weights still on it. Left the weights on there for about 5 minutes and took them off. And it has a little rocker now but it did dry the shit out of the base. So yes it does work.
05-13-2010 07:56 PM
hondarider17 K guys. i got my Jig and everything, ill post pics when im done.
Heat gun or boiling water??
05-13-2010 07:47 PM
legallyillegal heat jig heat snap
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome