Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Alternate Wax Methods Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
01-10-2010 03:31 PM
edwinx just to revive this old thread..

I am trying the heat gun method and did my board but I am wondering should the wax look when using heat gun? Basically, I am using the gun until the wax turns a bit shiny, should I melt it a bit more like until it is runny? I am worried I might burn the wax or my base. I am fairly good at moving the gun around to prevent hot spots.

Also, is this a replacement for hotwaxing? if not, how often should I hotwax?


Thanks,

Quote:
Originally Posted by Zee View Post
Rub rather than drip.

1. Crayon the wax on base
2. Heat up iron
3. Touch wax to iron and rub warm wax on base a section at a time until base is covered
4. Melt wax into base as you normally would (that is carefully, moving the iron constantly)
5. Scrape, brush, cork

This method uses way less wax than dripping, and I find you get more even coverage, and have much less to scrape off.


Heat Gun Quick Wax (Experts Only)
1. Crayon on the wax onto base
2. Heat gun on low, CAREFULLY melt the wax on to the base, move the heat gun constanty and fairly quickly. Holding the heat gun in one spot or holding it too close WILL damage your base.
3. Brush, scotchbrite or whatever, no scraping is necessary with this method.

I use this between full waxes sometimes, it only take 5-10 minutes.

02-23-2008 12:08 AM
Minger yeah, no paper here either. Just the smearing vs dripping
02-22-2008 02:25 PM
Zee
Quote:
Originally Posted by Minger View Post
The way that I do it is Heat wax and then quickly put a streak in a board, and repeat...its better than leaving it dripping for too long and then realiziing oh $#@%$ the wax is smoking because its on the iron.

I do it like: YouTube - #318 How To Wax A Snowboard

But I never thought of crayoning and then just melting that.
That's how I do it, except I've never used paper like he does in the video, that is interesting. I will try that.
02-22-2008 02:06 PM
Zee
Quote:
Originally Posted by totalgeek View Post
Thanks for the tip. I noticed at the end you say scrape, brush, cork. Does corking at then end (I do pad and nylon brush) give a better coating or make the wax absorb more into the base?
I like to course brush first, to get any excess wax off, then cork to smooth, then finally fine brush to structure. Everyone seems to have their own methods/reasons here though.
02-22-2008 01:46 PM
Minger The way that I do it is Heat wax and then quickly put a streak in a board, and repeat...its better than leaving it dripping for too long and then realiziing oh $#@%$ the wax is smoking because its on the iron.

I do it like: YouTube - #318 How To Wax A Snowboard

But I never thought of crayoning and then just melting that.
02-22-2008 12:45 PM
totalgeek Thanks for the tip. I noticed at the end you say scrape, brush, cork. Does corking at then end (I do pad and nylon brush) give a better coating or make the wax absorb more into the base?
02-22-2008 12:18 PM
Zee
Alternate Wax Methods

Rub rather than drip.

1. Crayon the wax on base
2. Heat up iron
3. Touch wax to iron and rub warm wax on base a section at a time until base is covered
4. Melt wax into base as you normally would (that is carefully, moving the iron constantly)
5. Scrape, brush, cork

This method uses way less wax than dripping, and I find you get more even coverage, and have much less to scrape off.


Heat Gun Quick Wax (Experts Only)
1. Crayon on the wax onto base
2. Heat gun on low, CAREFULLY melt the wax on to the base, move the heat gun constanty and fairly quickly. Holding the heat gun in one spot or holding it too close WILL damage your base.
3. Brush, scotchbrite or whatever, no scraping is necessary with this method.

I use this between full waxes sometimes, it only take 5-10 minutes.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome