|Topic Review (Newest First)|
|12-17-2013 12:48 PM|
Having the same problem with my Rome Mod Rocker and Flux Bindings. It's still a newish board so I doubt/hope it's not the inserts. However after years of hearing or being told that all boards have the same screw insert depth and it's the base plate thickness that effects the screw length. I decided to check with my old Burton and Capita boards. Turns out the Burtons insert is at least 2mm deeper than the Capita insert.
I'll measure the Rome insert and the Flux base plate depth tomorrow and buy the appropriate size screws. If they stay fixed tight I'll repost for any other poor bastards like myself and OP having the same problem.
|03-05-2012 03:22 PM|
|CheeseForSteeze||Sure am. It pays the bills and good thing because my snowboarding doesn't. It does the opposite.|
|03-05-2012 03:20 PM|
Originally Posted by CheeseForSteeze View Post
|03-05-2012 02:58 PM|
Just loctite them yourself. The key to threadlocking compound working is to use just enough so the thread troughs get compound and letting it set for at least 24 hours at room temperature. Otherwise, it won't work. I've used it on hundreds of folding knives (pivot screw) and motorcycles as well. It works if you use it right.
Keep in mind that threadlocking compound doesn't keep screws tight. It just prevents relaxation due to acoustic noise, which a snowboard (especially at high speed or over textures like granular snowpack) experiences lots of. The actual tightness of threaded members is caused by the longitudinal stresses developed by straining the bolted members when tightening past the point where physical interference occurs. This increases the normal forces on the planes of the threads which is what develops the friction that causes resistance to torque. In other words, if you don't put some muscle behind it, threadlocker won't do anything by itself. Get yourself a quality number 3 phillips head screwdriver with a good handle.
|03-05-2012 02:12 PM|
Maybe consider purchasing binding screws that have the 'Loc Tite' coating.
|03-05-2012 02:03 PM|
Nothing sucks more than loose bindings on the mountain.
Was at Copper Mountain once when one of my bindings came off and I could not for the life of me get it back on, it was a deep powder day and the bindings were iced over which made it difficult. This happened within minutes of last lifts closing so I was stuck for time. They had to snowmobile me off with one of the dog patrollers looking for people at the tree line. It took an hour to get back down due to his route. Was kind of fun actually, but something I'd rather not repeat. Now I check tightness at every break.
|01-21-2012 11:02 AM|
Just a quick question do you have another snowboard,try the bindings on there and see if they still lossen.
Then you will know if the bolts are to long/short or if your stretched the insert
|01-19-2012 07:54 PM|
|fattrav||Yeah, the initial screw in will be a little firm. Once the loctite has grooves in it, it'll be easier to screw in and out.|
|01-19-2012 01:23 PM|
|h-d||just got a new pair of bindings with thread lock on them...is it normal that you need to put a lil more preasure when screwing the binding to your board..compared to screws with no thread lock?|
|03-01-2011 12:09 AM|
Originally Posted by henry06x View Post
I think honestly the problem was that i didnt remove my bindings last season when i stored my board, why i dont know but i found out i didnt when i took it back out. Those bindings were on there tight as fuck i had to torque it hard to loosen them. Wonder if i screwed up the inserts abit leaving it tight like that all offseason...
|This thread has more than 10 replies. Click here to review the whole thread.|