Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Brand New Board- Detune The Tips? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-01-2012 11:49 PM
boarderbud if you do decide to detune. find the widest point on tip or tail of board and go an inch back from that rounding it off. better to use a stone or just be light with the file
03-01-2012 10:36 PM
CheeseForSteeze I like mjne rounded off on the nose/tail but you don't have to do this. The only board I've ever had factory detuned was the Draft.
03-01-2012 10:21 PM
Qball
Quote:
Originally Posted by pdxrealtor View Post
Either I got a used board of the board came with tips that are de-tuned.

Sno you have PM.
i think capita does that. my charlie slasher came with the tip and tail detuned
03-01-2012 09:35 PM
pdxrealtor Either I got a used board of the board came with tips that are de-tuned.

Sno you have PM.
02-29-2012 10:14 PM
pdxrealtor
Quote:
Originally Posted by AAA View Post
I'd give it my own wax job (factory jobs stink) and get on it. Then you can evaluate if the nose or tail feels hooky. How to tell? If you're carving and you notice that when you set the board high on edge, it tends to crank an insanely tight turn rather unexpectedly, or if you find the nose is wanting to fold when the board is heavily pressured, the nose is hooky. If you find the board doesn't want to cleanly release from a carve and wants to hold on and steer you into the trees, then the tail is hooky. If you find you have to detune at all, just barely knock the first few cm's of the razor sharp edge off with a few passes of a stone. DON'T round it! The edge should still look very much square with no discernable rounding. You just want to take the "bity-ness" out of it, and only if you NEED to.
Awesome info. Wax job for sure. A side from that your advice good and well noted. Most likely why SW rides out of the box and makes the adjustments if needed.

I will in box, wax , and head to meadows. Hint hint in case SW wants to guide a tour down HC.
02-29-2012 09:39 PM
AAA I'd give it my own wax job (factory jobs stink) and get on it. Then you can evaluate if the nose or tail feels hooky. How to tell? If you're carving and you notice that when you set the board high on edge, it tends to crank an insanely tight turn rather unexpectedly, or if you find the nose is wanting to fold when the board is heavily pressured, the nose is hooky. If you find the board doesn't want to cleanly release from a carve and wants to hold on and steer you into the trees, then the tail is hooky. If you find you have to detune at all, just barely knock the first few cm's of the razor sharp edge off with a few passes of a stone. DON'T round it! The edge should still look very much square with no discernable rounding. You just want to take the "bity-ness" out of it, and only if you NEED to.
02-29-2012 06:50 PM
Extremo I wouldn't worry about detuning the contact points. The BSOD is rev cam at the tips. Just wax and ride.
02-29-2012 05:31 PM
pdxrealtor Thanks both.. great advice to lay on table and see where the edge contact starts... !! Duh! lol...

Think I'll just wax it up and go.
02-29-2012 04:46 PM
earl_je why not ride it FIRST then decide if you need to detune it?? if you dont do park/rails and love to carve, you should just keep it the way it is.
02-29-2012 02:39 PM
pdxrealtor
Brand New Board- Detune The Tips?

Just ordered a new board, Capita BSOD, and was wondering if I should de-tune the nose/tail. If so, how much rounding? What type of file, or just use a stone? How far back do I go?

I like to carve so how far back I go scares me.

No park/rails etc...

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome