Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: NeverSummer SL stance offset / setback? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-15-2012 11:44 AM
Kapn.K Measure the distance from the front-most holes to the tip. Measure the distance from the most rearward holes to the tail. The second measurement is less. "IF" you want them the same, you'll have to move the back binding up one set of holes. In other words, they set back the whole set of mounting holes. This helps in powder. I've got a legacy and I think it's the mid-wide version of the sl. I have my rear binding up a set so it feels the same when riding switch. If you aren't ever going switch, I wouldn't worry about it.
03-15-2012 07:38 AM
ETM Cut piece of paper to your stance width and move it up and down until you get the measurements you want at each end. Mark the centres and then put your binding discs on, work out which holes on the board and the discs give you the correct setback which I believe is 1/2".
03-15-2012 06:06 AM
Tom W I seem to have the same dilemma trying to set up bindings on my new SL.

There is no reference point or default holes.
Setback apparently should be only around 0.5 to 0.75".
But for me it is more than 1.5" now.

Counting from the middle of the board I used the 2nd and 4th screw hole in the front binding.
And the same - 2nd and 4th from the middle on the back binding.
Distance is nice 21". But the setback seems 1.5" so too big?

Refer to above posts shall I move back binding up to the front by one hole.
Seems like it but again it makes little sense and I am supposed to carry a measuring tape to work out the correct holes?

Maybe I am being stupid but never had this problem before as there were default holes marked as reference.

Help please
02-16-2011 04:16 PM
dasob85 I actually emailed them about this. Unfortunately, I was still slightly confused. but here is what they said:

Basically, If you were to have your front binding mounted all the way toward the tip of the board, the back binding would need to be moved up one hole set from the bottom of the board to have a twin set-up. If you had your bindings set down 1 hole set on the tip, then you would have to move the back binding up two hole patterns in the back, etc. I hope this helps!

I used the second and fourth holes from the head of the board on the front foot, and the 3rd and 5th holes counting from the head on the back foot. Hopefully that all makes sense.
02-15-2011 02:16 PM
NeverSummer SL stance offset / setback?

What's up with the NeverSummer SL stance offset / setback? I can't find the info on their company website.

To take full advantage of the progressive sidecut, what's the best way to mount bindings on the SL with correct stance offset / setback? I do not see any reference marks on the board.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome