Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: How tight should I be tightening my boots? (Burton Ions) Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
12-22-2012 04:53 PM
Racer20 Try without the superfeet. Those are thicker than the stock insoles and raise your foot up, which can cause this problem. Superfeet are not much better than stock inserts if they aren't the right shape for your boots and feet.

I have had 3 pairs of ions, and I have the same issue if I over tighten the bottom. As others have said, try leaving the bottom loose, and put the j-bars in to hold your heel tighter.
11-26-2012 12:57 AM
Ballistic Bottom loose and top snug, its how i ride always. If im hitting some gnarly black diamonds i tighten up sometimes.

Another tip, and i always do this... My first couple runs of the day my boots are kept comfy loose. Then i tighten them a little bit each subsequent run for next couple runs. If i start off with boots too tight my feet cramp up everytime.
11-23-2012 11:11 AM
StreetDoc I ride Ion's and sized them just like you, my issue with them is they're very easy to overtighten. Usually after the first run my feet are hurting and I have to loosen them a bit. I like them just snug enough to not feel loose.
11-23-2012 10:29 AM
Triple8Sol Also make sure you're not overtighening the inner liner. That is a common mistake that even I was guilty of up until more recently.
11-17-2012 09:43 AM
threej21 yea, what everyone else said. when i first got speed laces, i found that overtightening is easy to do, and first few times out on them i always had to loosen the bottom zone after my initial lacing

think its because its sooo easy to make them that tight that you think you should. but yea, try doing the upper pretty tight and leave the lower with a bit more room

also, side thought, you could try putting a click or two of forward lean on your bindings to help eliminate heel lift
11-17-2012 09:09 AM
Lamps On my ions I wears the liner snug, the upper zone super tight, and the lower zone medium to moderate tight or I get the same pressure/pain in the ball of my foot. Remember the speed zone laces have a lot of leverage, especially the bottom zone.
11-17-2012 06:32 AM
wrathfuldeity Try to heat mold first....but you can add or take away liner material. Adding involves adding bits of adheasive foam...and taking away involves shaving bits of the liner off. Put your foot in the liner, use a sharpie to draw or shade in exactly where the pressure points are. Then carefully remove a bit of the liner...I'd use a grinding wheel or a small grinding wheel on a drill or a wood rasp to just take-off maybe a 16th or 8th of an inche off that spot. Then go ride and see if that does it, if not repeat. Once you get it tweaked then smear a bit of McNett freesole on top of the grind spot to keep the liner intact.
11-17-2012 05:02 AM
ETM heat mold .
11-17-2012 04:48 AM
Giannis I have wide feet at the front, so what i do with my Burton boots is that i tighten the liner pretty well, the upper zone as well and leave the lower zone looser. That way i dont get heel lift and the sides of my feet dont hurt. During the day i might tighten the lower zone a bit more when i am warmed up. Hopefully, after a few days they will pack out more.

Unless you are doing something weird with the bindings. Is the toe strap centered and not too much over your toes?
11-16-2012 10:26 PM
How tight should I be tightening my boots? (Burton Ions)

So this is my 4th season boarding and I've replaced all my gear. I've used rentals and second hand crap that have left me with sore feet and terrible heel lift for the past 3 years and after putting a huge chunk of change away and testing out a bunch of boots in shops I decided on the Burton Ions. I've done 3 days in them and I have to say, I'm really, really bummed out

In the store they fit great (a little tight, but I bought a half size down for packout). After the first 2 days they packed out beautifully. Almost absolutely zero heel lift and they rode exactly how I had hoped. One small problem - PRESSURE POINTS!!! On the inside of both my feet right above the ball of my foot it hurts like CRAZY after 2-3 runs. If I loosen the liner/boot then it somewhat goes away but then I get F***ING HEEL LIFT! Oh, and I've already had them heat molded and have Super Feet footbeds

So how tight should I be tightening my boots? To get zero heel lift I tighten them ALL the way. I mean I seal the velcro on that liner tight, tighten the liner good, and pull those speed laces tight enough that the boot feels like it's molded around my foot. If not for those pressure points they would be PERFECT at that tightness. Am I tightening too tight? Did I just spend $450 on boots that aren't actually right for my foot? Ugh..

EDIT: Also I'm strapped into Cartel ESTs so I don't think it's a binding issue, unless the specifics of my binding setup could be causing such issues?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome