|Topic Review (Newest First)|
|01-02-2013 08:28 PM|
Originally Posted by Datfoooo View Post
Again it's all a personal preference thing, just try it out and make adjustments as needed.
Here's a couple things to remember though:
1) Always properly tighten the screws even when making "test adjustments". I use a cordless drill with the adjustable clutch set to about 10 out of 16 on my Mikita. They should be quite hand tight. Not so tight that you're about to strip the screw heads, but tight enough that they're not going to back out.
2) Don't make more than one adjustment at once (to angle, width, forward lean, etc. etc.). If adjusting angle you can adjust both bindings at once until you're relatively comfortable, then make fine adjustments after that. Ride it for AT LEAST a few runs if not a few days, then play with stance width or vice versa.
3) Don't try to fix poor snowboarding habits with odd binding positions. Unless you have a very different frame than the average person, a stance width from 20-23" is about normal, and binding angles with a difference of 18-24 deg is about right. Forward lean should JUST touch the back of your boot with them strapped in (without you in them), and as a beginner you can start with less forward lean than that. It doesn't hurt to have some forward lean though to teach you to bend your legs. If you hit a plateau with your boarding take a lesson before you start changing your setup thinking it's the board. It's usually you.
4) Having the overhang equal on each side is a pretty important step of a first setup. After mounting the bindings where you think they should go, and moderately tightening the screws, tie up your boots and mount them in the bindings. Strap them in and then lean the board on either edge while pressing the edge down to make contact (on a camber or flat board). The amount of lean angle you get before the toe or heel touches should be roughly equal.
Have fun! I enjoy setting up boards/bindings... You learn a lot!
|01-02-2013 04:10 PM|
Originally Posted by phony_stark View Post
|12-27-2012 05:03 PM|
$50.00 is fucking ridiculous. Do it yourself. I'm assuming you know how to use a screw driver.
As for stance width, take a string and go from your knee to the floor. That's a good place to start.
Angles are all preference. make sure that your backfoot is zero or less and play around to see what works for you and feels neutral. It's something you'll end up changing a lot when you first start riding.
I started with 15-0 front/back and as I started to ride switch more went to 15/-6 and now I'm at 12/12.....
Basically the goal is, to get something that feels nice and neutral/natural when you're standing on ur sn0slider.
|12-27-2012 03:37 PM|
DAFUQ? Sportmart charged me $5 to adjust them to suit when I was first starting. AND they showed me how to do it.
Was kind of embarrassed to realize how easy it was.
|12-27-2012 12:58 PM|
Originally Posted by triumph.man View Post
|12-27-2012 12:54 PM|
|triumph.man||i'll charge $25 its all a matter of preference really. whatever is most comfortable if you are just starting out. I'll make it maybe 20 on the front and 10 in the back if you are just starting out and just like to go down the mountian|
|12-27-2012 12:40 PM|
Need suggestion for beginner
Hey this is my 3rd year snowboarding..just picked up a pair of 2012 Mission EST bindings and need some help with my stance. The local shop here wants to charge 50.00 for mounting and adjusting...
Can anyone shed some light on what degree a beginner should be riding? I have always rented my equipment. I ride regular not goofy...i read online that maybe adjusting my stance to be 12 degrees front and -12 on the back or 16 front and -6 on the back?