Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Cracked Union Force binding plate Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-11-2013 10:45 PM
Cyfer Loc-Tite and plastic parts are a complete no no. As stated above allow loc-tite to dry on the threads before using the screws. Never needed it before, call Union I bet they will provide you with new discs but you don't need Loc-Tite to mount bindings in the future.
02-11-2013 10:40 PM
airblaster503 If you used Loctite you need to make sure it is dried before using the screws. Any contact while wet with your baseplate will cause the nylon to basically crumble. Plus Union hardware already comes with blue Loctite on the screws so you shouldn't need to add any.
02-11-2013 10:25 AM
BurtonBindings http://www.unionbindingcompany.com/info-distribution

there lives your answer, on the internet, from the company that makes your product.
02-11-2013 12:24 AM
Mojo ok, its option 1. I did use loctite... didnt realise that it weakens the plastic. Damnit... my bad?!?!

Pics to come if still required but fractures are all around the area where the screw head meets the plate & around the slot where it meets the board. Plates are currrently useless.

Everything else, ive done by the book, washers, hand tighten.

Bindings were purchased online frm the US, im in Australia. 1st set of replacement plates were sent out to me via post few yrs ago, postage at my expense.

Do you have the Union Reps contact details(email) to get replacement plates?
02-11-2013 12:06 AM
Cyfer Dude!! I've used Union contacts for years, stomped huge jumps on em and even beat the crap out of my rig in spring conditions. I've briken every part of a binding except two in 14 plus years of riding, baseplates and discs. Whatever you're doing not using the washers, using lock-tite, or a power screw driver. I've worked in a shop for a few years too and never seen a broken disc, not once. Pictures would help to see what's going on.
02-10-2013 11:58 PM
BurtonBindings One of two things is likely happening:
1: you used loctite on your screws and the loctite is eating the disc causing it to fracture.
2: you aren't using the mounting washer that Union supplied causing a greater load at a more localized point. (point load).

if it's neither of these two; i wouldn't know what to tell you. Union's disc are made of a very robust nylon. your best best is to call the shop that you bought them from or Union / Union Distributor.
02-10-2013 10:47 PM
Mojo I did, the plastic plates seem to be very brittle and crack after the bindings get used. I initially tighten them by hand as one would, they seem to be ok but on removal of the screws to adjust my binding or for transport, ive found cracks in the plates and they have become useless by that point.

1st set of plates i had, i noticed my bindings moving a little while i was on the board, i unstrapped and found the broken plate, screws loose.
02-10-2013 10:38 PM
scrotumphillips How are you cracking them? You are only supposed to tighten the screws by hand.
02-10-2013 10:33 PM
Mojo
Cracked Union Force binding plate

Has anyone else using the Union Force bindings have issues with the plate that holds the binding to board(where you adjust your angle) cracking? As its made of plastic, both mine has cracked where the screw heads goes in from the pressure of the screws. Ive gone thru 2 sets of plates now & both has cracked, i even reduced the pressure(tightness) of the screw on the 2nd set of plates i got but they both cracked after just a few days on the mountain.

Can i get a replacement plate that is made of metal?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome