Snowboarding Forum - Snowboard Enthusiast Forums - Reply to Topic
Thread: Painting binding ratchets Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Snowboarding Forum - Snowboard Enthusiast Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-15-2013 01:27 PM
jbernste03 I painted my ratchets and they work fine.. been on the mountain at least 10 times since painting and only minor chipping.. no problem at all with the fucntionality of them

1. plastic/ metal primer
2. plastic acrylic - many layers
3. made for outdoors - flexible/waterproof clearcoat

02-15-2013 07:29 AM
edlo Don't try to paint plastic. If it is metal get some blue tap and put it on everything you don't want to paint. Sand finish off the existing with some 200 grit paper or foam sanding block. Get some spray primer , don't over do it with the primer. Paint let dry, then clear coat, wait a couple of day. It will cost you over $20 for the supplies if do don't already have it. When you are done with the spray paint turn it upside down and spay until just air comes out. Any type of handy person will have some spray primer, clear coat will be harder, ask a car guy.
02-12-2013 05:17 PM
Originally Posted by ecks View Post
For sure, its a huge hassle and never stays. I had a shitty rental board that I bought after season for $30 when I first started and painted it a couple times and no matter how many layers of paint or clear coat I used it never stayed.
Sounds like you might have messed up. It doesn't matter how many layers of paint you put on, in fact more doesn't equal better. If you're painting anything, the most important step is surface prep, and the second most important step is having the right primer. Primer will bond with the surface and the paint, and nothing should come off. Painting a snowboard isn't particularly difficult, as the main surface your working with is usually a fibreglass resin that most primers will stick to...

That said, the ratchets will be significantly harder. They look almost like they were powder coated from the factory (although I've never held them to check) and powder coating is WAY tougher than paint as far as durability.

Painting the highbacks or baseplates is one thing, but I think painting major wear items on bindings would be a no go... It is possible but not easy to make it last.

Just my $0.02 of course.

If they're metal you could take them somewhere and have them re-powder coated a different colour, chromed, or just polished. The thing I like about the Burton ratchets is they're usually just coloured metal. Nothing really to wear off.
02-12-2013 03:31 PM
ecks For sure, its a huge hassle and never stays. I had a shitty rental board that I bought after season for $30 when I first started and painted it a couple times and no matter how many layers of paint or clear coat I used it never stayed. I can imagine bindings would have the same problems.

02-12-2013 01:30 PM
sheepstealer Thanks ecks...yeah...probably not going to paint them, Don't want to deal with all that hassle.
02-12-2013 09:31 AM
ecks Probably not a good idea. If you want it to stay for more than a single run you would have to sand them down, paint a couple layers of automotive paint and clear coat. IMO not worth the hassle and a couple mm of paint on the inside of the ratchet could cause problems.

Depending on what your trying to do you may want to check out just getting a sheet of vinyl and cutting it to spec. Wouldn't ruin the paint and you can take it off. Just a thought.
02-12-2013 09:26 AM
Painting binding ratchets

So the ratchets to my Rome 390 Bosses have been failing recently - they won't engage, especially in the cold. I got in touch with Rome support and Carl sent me out some new ratchets - awesome!

Would it be a bad idea if I wanted to paint them? Nothing crazy or ornate, just wanted to add some highlights to my setup. I don't want to ruin the ratchet mechanism though - what (if any) paint would be OK to use for this endeavor?

Ratchet pic is below (courtesy of Wiredsport's thread on the new 390 Bosses. Note I am only using this picture as a reference to the ratchets, nothing more).

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3
For the best viewing experience please update your browser to Google Chrome