Snowboarding Forum - Snowboard Enthusiast Forums

Snowboarding Forum - Snowboard Enthusiast Forums (http://www.snowboardingforum.com/forum.php)
-   Snowboard Reviews (http://www.snowboardingforum.com/snowboard-reviews/)
-   -   2010 Custom X First Thoughts (http://www.snowboardingforum.com/snowboard-reviews/26270-2010-custom-x-first-thoughts.html)

SobeMike 03-04-2010 03:48 AM

2010 Custom X First Thoughts
 
Board: 2010 Custom X 158
Bindings: 2010 Cartel (3D with adapter plate)
Boots: 2010 Ion


I got my Custom X on Saturday and I got up on Verbier with it on Wednesday. We did 30 miles and 18 thousand feet of vertical on a combination of Reds (US Blue equivalent but usually more challenging), blacks, ungroomed blacks, and off piste blacks. The snow conditions were varied as it was fairly crap at the bottom but up a 9 thousand feet it was nice powder although not very deep. The visibility was bad which made it a bit more challenging for the day.

I had already hot waxed the board so I never used the factory wax on it.

The first couple of warm up runs went well and I had no issue with the stiffness of the board even though I was coming of a 56 Guru. In fact, I really didn't notice too much difference on the easy runs we started off on. After the warm up we decide to go hit a 6 mile off piste run with significant moguls. Here the stiffness was really apparent and any misdirection which lead to going over rather than around a mogul would end in flight and if I am honest a couple spectacular wipeouts. I would have to say that a flexible board might be nicer for moguls but I'll give it a few more shots before I can make that decision.

Over the day I only noticed a few things about the board. As you would expect, it is super super stable at high speeds. I never got it to chatter and it goes rail to rail much more efficiently and cleanly than my Guru. In fact, it handles the speed so well that you can forget that you are traveling at a decent clip and catch an edge on a path (happened once toeside and hurt badly). The main difference aside from the stability and edge to edge responsiveness was the fact that you cannot make this board turn on groomers without having your weight forward. That little tidbit lead to an epic fall near the end of the day when I went straight while trying to initiate a turn and then initiated the turn while airborne resulting in a large amount of pain and laughter from friends.

Later in the day we hit Tortin which is considered one of the scariest runs in the world. The board performed absolutely flawlessly. I think it was helped a lit by the fact that there had been decent snowfall so the moguls were considerably shorter than normal. It handled the 40-45 degree start perfectly and the 30 degree ungroomed run down to the bottom admirably.

Now let me dispel some myths. When I was looking to buy this board I almost didn't because of the following things I read:

It's for Advanced riders only: BS. It is for riders who know how to carve and don't use their back foot to turn.
It accelerate very quickly: Never noticed this on steeps but on flat land it can keep up with or even beat skiers.
it will take many days to adjust to this board: Not in my case so I wouldn't buy into it being the same for everyone.
It needs to have the front and back edges detuned. I didn't and I was fine except for when I screwed up and then it ate me alive like any other board would.

Conclusion:

It's only been one day but so far it is the best board I have been on. It is predictable, fast, stable, very easy to rock edge to edge, and looks great. The wax job was gone by the end of the day but after 30 miles I guess I shouldn't complain. I would say the only thing to be careful with is to make sure, even as you get tired later in the day, that you keep your weight forward to allow the board to turn. Other than that, it works like any other board but just seems to feel sharper and much crisper but will catch air easily if you hit a bump.


Hope this helps. If you have any questions let me know.

Hoons 03-04-2010 08:49 AM

nice review :thumbsup:

Mr. Polonia 03-04-2010 09:27 AM

yea pretty good review..i really like the '10 graphics and i was planning on getting it in spring, but the '11 custom x looks sweet too and it has the frostbite edges so i guess ill wait til next next spring to get that instead:(

SobeMike 03-04-2010 11:41 AM

Thanks, I will post more next week as I should be going for the next three days. Hope we get some snowy nights and clear days!

Reede 03-04-2010 05:09 PM

Quote:

Originally Posted by Mr. Polonia (Post 268422)
yea pretty good review..i really like the '10 graphics and i was planning on getting it in spring, but the '11 custom x looks sweet too and it has the frostbite edges so i guess ill wait til next next spring to get that instead:(

Explain frostbite edges to me, sounds like some kind of icy conditions tech.
I want a board that handles shitty Australian icy conditions better than my regular custom ICS does and the Custom X is probably the likely candidate, or a T6 if I feel like going overboard =)

Mr. Polonia 03-04-2010 05:17 PM

Quote:

Originally Posted by Reede (Post 268772)
Explain frostbite edges to me, sounds like some kind of icy conditions tech.
I want a board that handles shitty Australian icy conditions better than my regular custom ICS does and the Custom X is probably the likely candidate, or a T6 if I feel like going overboard =)

im not really too familiar with it but its an improved edge hold on some of the 2011 burton boards.
Just how lib tech has magnatraction, burton has frostbite edges.

Any board that is stiffer will have better hold...and the custom x is pretty darn good in any condition way better than the softer custom. Im happy with my 09 custom x and i bet the '11 will be even better

Reede 03-04-2010 06:20 PM

Any significant change over the current lines PDE? Im always interested in the new tech from an engineering standpoint.

Maybe they just wanted to give the tech a cooler name. PDE doesnt sound anywhere near as cool as megnetraction.

Mr. Polonia 03-04-2010 09:13 PM

Quote:

Originally Posted by Reede (Post 268821)
Any significant change over the current lines PDE? Im always interested in the new tech from an engineering standpoint.

Maybe they just wanted to give the tech a cooler name. PDE doesnt sound anywhere near as cool as megnetraction.

:dunno: PDE is pretty much that the edges by the bindings stick out a few mm, frostbite edges might be that they stick out even more for more edge hold...idk, but it sure is catchy


All times are GMT -5. The time now is 04:40 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0 PL2